隨著通風管道的使用年限，他出現的問題也會越來越多，正常情況下會出現很多的雜質，這個東西是不好清理的，如果不清理就會造成各個環節的損壞，濟南強順通風設備教你通風管道清理方法。
With the use of ventilation pipe life, he will be more and more problems, in normal circumstances, there will be a lot of impurities, this thing is not clean, if not cleaned up will cause damage to the various links, Ji'nan strong ventilation equipment to teach you the method of ventilation pipe cleaning.
濟南通風管道裝置時，進、出風日宜在風道預制時開出洞口，如需在裝置終了的風道上現開風口，其接口處應緊密。當運送含凝結水或含濕量較大的氣體時，其水平管道宜設有坡度，并在低點處接排水管。裝置時風道底部不宜呈現縱向接縫，對底部有接縫處應中止密封處置。山東通風管道加工工人提醒好是三個月進行一次清潔，這樣既可以保證平時正常的運轉，還可以延長通風管道的使用壽命，
When the air duct is made in Ji'nan, the inlet and outlet should be opened when the air duct is prefabricated. If the vent is needed in the end of the air duct, the interface should be close. When transporting gas containing condensate or large moisture content, the horizontal pipeline should be provided with a slope, and the drainage pipe should be connected at the low point. The longitudinal joint is not suitable for the bottom of the duct, and the sealing treatment should be stopped for the joints at the bottom. Shandong ventilation pipe workers remind the best of three months to carry out a comprehensive cleaning, so that it can ensure normal operation and prolong the service life of the ventilation pipe.
當風管與風機銜接時，應在進出風口處加軟接頭，其軟接頭的斷面尺度應與風機進出風口共同。雙吊桿支架在風道就位后，應保證橫擔平直，吊桿不改動，雙吊桿受力均勻。軟管接頭普通可采用帆布、人造革等材料，軟管長度不宜小于200，松緊度應適宜，柔性軟管可緩沖風機的振蕩。
When the wind pipe is connected with the fan, the flexible joint should be added at the inlet and outlet. The dimension of the soft joint should be in common with the inlet and outlet of the fan. When the double hanger bracket is positioned in the air duct, the cross arm shall be straight and the boom shall not be changed, and the double hangers should be evenly distributed. Hose joints can usually be made of canvas, artificial leather and other materials, hose length should not be less than 200, tightness should be appropriate, flexible hose can cushion the oscillation of fans.
當風道與除塵設備、加熱設備等銜接前，應待設備裝置終了后，按理論測繪的圖紙中止預制和裝置。對運送易燃、易爆氣體的鋼板風道，在風道銜接法蘭處應裝置跨接線，并與靜電接地網銜接。
When the air duct is connected with the dust removal equipment and heating equipment, the prefabrication and installation shall be stopped according to the theoretical surveying and mapping drawings after the end of the equipment. For the steel air duct conveying inflammable and explosive gases, the connection should be installed at the connecting flange of the duct and connect to the static grounding grid.
當水平風道高度在4m以上時，裝置人員應系帶。腳手架或移動式支架上的跳板應固定好，跳板寬度應契合規范，在腳手架上的裝置人員宜攜東西袋，避免東西或電鉆等物掉落傷人。
When the height of the horizontal airway is above 4m, the installation personnel should fasten the seat belt. The springboard on the scaffold or the movable support should be fixed. The width of the springboard should be in accordance with the safety specification. The device personnel on the scaffold should carry the bag to avoid the thing or the electric drill.
對于清潔這方面的問題還有不明白的，可以通過我們的官網http://m.pvcbox.cn/咨詢我們，或直接咨詢山東通風管道加工師傅，我們將為您詳細解答。
For the cleaning of this problem is not clear, can be consulted through our official website http://m.pvcbox.cn/, or direct consultation with the Shandong ventilation pipe processing master, we will give you a detailed answer.
上一篇：螺旋風管通風系統的作用范圍介紹
下一篇：通風設備系統您了解嗎？
