Cooking fume purifier cleaning process, for soot pipe cleaning is also very important, the vertical flue cleaning, commonly used in two ways:

　　1.機械設備法，向煙道內噴灑化油劑后，用高壓清洗機進行清潔。此方法容易操作、難度小、工作量較小、費用低的清潔方式，但對于清潔周期為半年以下的豎道煙道，這種清潔方式無疑是佳的選擇。

　　1. mechanical equipment law, to spray oil in the flue, after the use of high-pressure cleaning machine for cleaning. This method is the most easy to operate, the least difficult, less work, the lowest cost cleaning method, but for cleaning cycle for half a year under the vertical flue, this cleaning method is undoubtedly the best choice.

　　2.開孔法，由技術人員測算出需要開孔的間隔距離、開孔位置、大小和數量，通過這些孔對煙道內進行清洗。后對每個孔進行密封處理。此方法相對難度大，費用相對較高，但清潔效果很徹底

　　2. opening method, by technical personnel to calculate the need to open hole spacing, opening position, size and quantity, through these holes to the flue cleaning. Finally, each hole is sealed. This method is relatively difficult, relatively high cost, but the cleaning effect is very thorough

　　正確清洗油煙凈化器十分重要，因為吸油煙凈化器上沾附的油脂和污垢是易燃物，且不易除掉，用戶可能會用易燃易爆的化學溶劑去清洗，操作不當會引起火災。通常采用中性清潔劑清理油煙凈化器表面時有以下幾個步驟：

　　The correct cleaning fume purifier is very important, because the oil smoke purifier attached on the grease and dirt is flammable, and not easy to get rid of, the user may use chemical solvents to clean the flammable and explosive, improper operation will cause a fire. The following steps are usually used when cleaning the soot purifier surface with a neutral detergent:

　　1.旋下油杯，倒去積油;

　　Unscrew the 1. cup, pour out the oil;

　　2.拆下濾網，放入加有中性洗滌劑的溫水浸泡，用軟刷將其清洗干凈;

　　2. remove the strainer and put it in lukewarm water with a neutral detergent and clean it with a soft brush;

　　3.用浸有中性清洗劑的濕布擦洗機體表面。其中應該倍加注意的是，清洗時務必拔掉電源插頭;嚴禁用水沖洗，防止電腦板析進水;以及嚴禁用易燃清洗劑。

　　3. scrub the body surface with a damp cloth dipped in a neutral detergent. It should be noted that when cleaning, must unplug the power plug; water is not allowed to wash, to prevent the computer board analysis of water; and strictly prohibited flammable cleaning agent.

　　公司始終堅持不斷進行管理創新和科研創新，將以的品質、完善的售后服務贏得廣大客戶的信賴與支持，歡迎廣大新老客戶來我公司實地考察，洽談合作!

　　The company always adhere to the continuous management innovation and scientific innovation, will win the support and trust of customers with excellent quality and perfect customer service service, welcome new and old customers to visit our company to negotiate cooperation!

上一篇：有效防止通風管道腐蝕的條件
下一篇：風管加工過程中的注意事項